在科技館或主題公園里，數米高的大型航天模型若想掙脫電線束縛，太陽能發電或許是實現 “自主供電” 的鑰匙。這種結合看似簡單，實則需要在能量平衡、材料適配與場景適應中找到精準的平衡點，讓模型既能保留航天美學，又能借助陽光實現電力自給。

　　In science museums or theme parks, if large space models several meters high want to break free from the constraints of power lines, solar power generation may be the key to achieving "autonomous power supply". This combination may seem simple, but it actually requires finding a precise balance point in energy balance, material adaptation, and scene adaptation, so that the model can both preserve aerospace aesthetics and achieve self-sufficiency in electricity through sunlight.

　　大型航天模型的電力需求集中在幾類設備：艙內模擬燈光（單組 5-10W）、互動顯示屏（20-30W）、小型機械傳動裝置（如艙門開合電機，50-100W），總功耗通?？刂圃?200W 以內。太陽能供電的核心是讓發電量覆蓋這些需求。以常見的 10 米長飛船模型為例，其外表面可利用面積約 8-12㎡，若鋪設效率 18% 的單晶硅電池板，在正午強光下（1000W/㎡）每小時可發電 1.4-2.2 度，完全能滿足實時用電，甚至有盈余可儲存。但室內場景需謹慎：玻璃幕墻的透光率通常僅 70%，加上燈光照明強度不足自然光的 1/5，發電量會驟減至室外的 10%-15%，需搭配儲能設備彌補缺口。

　　The power demand of large-scale aerospace models is concentrated in several types of equipment: cabin simulation lights (single group 5-10W), interactive display screens (20-30W), and small mechanical transmission devices (such as cabin door opening and closing motors, 50-100W), with a total power consumption usually controlled within 200W. The core of solar power supply is to cover these needs with the amount of electricity generated. Taking the common 10 meter long spacecraft model as an example, the available surface area is about 8-12 square meters. If a monocrystalline silicon solar panel with an efficiency of 18% is installed, it can generate 1.4-2.2 degrees of electricity per hour under strong noon light (1000W/square meter), which can fully meet real-time electricity consumption and even have surplus for storage. However, caution should be exercised in indoor scenes: the light transmittance of glass curtain walls is usually only 70%, and the lighting intensity is less than 1/5 of natural light, resulting in a sudden decrease in power generation to 10% -15% of outdoor levels. Energy storage devices need to be used to fill the gap.

　　實現這一方案，首先要解決電池板與模型外形的適配問題。航天模型多有曲面結構（如火箭頭部的圓錐面、飛船返回艙的球面），傳統剛性電池板（厚度 3-5mm）只能貼合平面區域，曲面部分需改用柔性薄膜電池（厚度 0.1mm，可彎曲至半徑 50mm），這類電池效率約 12%-15%，雖稍低但能完美貼合流線型外觀。安裝時采用輕量化設計：用結構膠（剪切強度≥15MPa）將電池板直接粘貼在模型外蒙皮上，省去支架重量，同時選擇碳纖維復合材料替代部分金屬結構，確保整體增重不超過模型自重的 5%，避免重心偏移影響穩定性。

　　To implement this solution, the first step is to solve the problem of adapting the battery board to the shape of the model. Aerospace models often have curved structures (such as the conical surface of rocket heads and the spherical surface of spacecraft return capsules). Traditional rigid solar panels (thickness 3-5mm) can only fit flat areas, and flexible thin film batteries (thickness 0.1mm, can be bent to a radius of 50mm) need to be used for curved parts. The efficiency of these batteries is about 12% -15%, which is slightly lower but can perfectly fit the streamlined appearance. Lightweight design is adopted during installation: structural adhesive (shear strength ≥ 15MPa) is used to directly paste the solar panel onto the outer skin of the model, saving the weight of the bracket. At the same time, carbon fiber composite materials are selected to replace some metal structures, ensuring that the overall weight gain does not exceed 5% of the model's self weight and avoiding the impact of center of gravity shift on stability.

　　儲能與電路系統是續航的關鍵。選用磷酸鐵鋰電池（循環壽命 2000 次以上，-20℃仍能保持 70% 容量）作為儲能核心，以 200W 功耗計算，配備 500Wh 容量的電池組（約 3kg），可在陰天或夜間支撐 2-3 小時。電路設計為 12V 低壓系統，通過 MPPT 控制器（效率 98%）優化太陽能轉化，將電池板輸出的 30-50V 電壓穩定降至 12V，同時加入防反接保護和過充過放模塊，避免陰雨天氣損壞電池。針對戶外場景，電池板需用耐候性封裝材料（抗紫外線老化 5000 小時以上），電路接口做防水處理（達到 IP65 等級），確保 - 20℃至 60℃環境下穩定工作。

　　Energy storage and circuit system are the key to battery life. Using lithium iron phosphate batteries (with a cycle life of over 2000 times and a capacity of 70% at -20 ℃) as the energy storage core, with a power consumption of 200W, equipped with a 500Wh capacity battery pack (about 3kg), it can support for 2-3 hours on cloudy days or at night. The circuit design is a 12V low-voltage system, which optimizes solar energy conversion through an MPPT controller (with an efficiency of 98%), stabilizing the 30-50V voltage output by the solar panel to 12V. At the same time, anti reverse protection and overcharge/discharge modules are added to prevent damage to the battery during rainy weather. For outdoor scenarios, the battery panel needs to be packaged with weather resistant materials (resistant to UV aging for more than 5000 hours), and the circuit interface needs to be waterproofed (up to IP65 level) to ensure stable operation in environments ranging from -20 ℃ to 60 ℃.

　　實際應用中需應對光照不均的問題：若模型局部被陰影遮擋，單塊電池板效率會下降 30%-50%，可將電池板劃分為多個獨立單元，每個單元串聯旁路二極管，使陰影區域不影響整體發電，效率損失控制在 10% 以內。此外，通過智能控制系統平衡能耗：光照充足時開啟全部設備（如動態演示、聲光效果），光照較弱時自動切換至節能模式，關閉非必要負載，優先保障核心功能運行。

　　In practical applications, it is necessary to address the problem of uneven lighting: if the model is partially shaded, the efficiency of a single solar panel will decrease by 30% -50%. The solar panel can be divided into multiple independent units, each connected in series with a bypass diode, so that the shaded area does not affect the overall power generation, and the efficiency loss is controlled within 10%. In addition, energy consumption is balanced through an intelligent control system: all devices are turned on when there is sufficient lighting (such as dynamic demonstrations, sound and light effects), automatically switched to energy-saving mode when the lighting is weak, non essential loads are turned off, and core functions are prioritized for operation.

　　這種太陽能供電方案，讓大型航天模型從靜態展品變?yōu)?“微型發電站”，尤其適合戶外長期展示 —— 不僅能減少電纜鋪設的成本與美觀影響，還能通過 “陽光發電” 傳遞綠色能源理念。當陽光掠過模型表面的電池板，轉化為點亮艙內儀表盤的電流時，這些 “地面上的太空夢想” 便有了更生動的科技注解：既復刻了航天器的能源邏輯，又讓普通人直觀感受到太陽能與航天科技的奇妙共鳴。

　　This solar powered solution transforms large aerospace models from static exhibits into "micro power stations," making them particularly suitable for long-term outdoor displays. It not only reduces the cost and aesthetic impact of cable laying, but also conveys the concept of green energy through "solar power generation. When sunlight passes over the solar panels on the surface of the model and is converted into electricity to light up the dashboard inside the cabin, these "space dreams on the ground" have a more vivid technological annotation: they not only replicate the energy logic of spacecraft, but also allow ordinary people to intuitively feel the wonderful resonance between solar energy and aerospace technology.

　　本文由大型航天模型友情奉獻.更多有關的知識請點擊:http://www.6re0un.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from a large aircraft model For more information, please click: http://www.6re0un.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message